Duct Repair & Sealing Cost in Manchester - We Measure the Leak Before We Quote

We measure the actual leakage before recommending any work, then put the scope and the price in writing. You are paying to fix a measured problem, not a guess.

✓ Licensed & Insured ✓ Written quotes ✓ Free estimates
Call (833) 865-1627

Call to schedule your free estimate

Work is performed by our local vetted partner.

🛡 Licensed & Insured 📝 Written Fixed-Price Quotes 💲 Upfront Pricing · Free Estimates
Whole-home duct cleaningWhole-home duct cleaning
Dryer vent cleaningDryer vent cleaning
Camera inspectionCamera inspection
Sanitizing & deodorizingSanitizing & deodorizing
Every visit starts with

Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents

Worth knowing

That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.

Get your free estimate
Explore

Styles & brands we work with

  • Whole-home duct cleaning
  • Dryer vent cleaning
  • Camera inspection
  • Sanitizing & deodorizing
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Questions about your air duct cleaning?Free estimate, price agreed before work starts
Call (833) 865-1627

How Much Does Duct Repair & Sealing Cost in Manchester?

Duct repair and sealing in Manchester, NH typically runs $180 to $950 for most residential jobs, with the average homeowner landing somewhere around $420. A single disconnected joint or small leak sits at the low end; a whole system of leaking branches, crushed flex runs, or resealed main trunks pushes toward the top. We set the final price per job with a free written estimate, so what you see here is a planning range for 2026, not a quote.

Those numbers matter in a city with Manchester’s housing stock. Duct systems in the older triple-deckers and mid-century capes around downtown and the North End have usually had work done on them before, sometimes well, sometimes not, and a proper assessment is what tells you which repair tier you’re actually in. We begin with the assessment, not the estimate.

Key Takeaways

  • Typical duct repair and sealing jobs in Manchester cost $180 to $950, depending on how many leaks and how many disconnected runs we find.
  • Sealing alone is the lower-cost option; repairing crushed or disconnected ducts costs more because the run has to be opened up and rebuilt.
  • We use professional-grade Rotobrush and Nikro equipment to inspect and clean before any repair, so we’re not sealing over debris or a compromised system.
  • We repair ducts, not just clean them. That capability is the difference between fixing the problem and working around it.
  • Our technicians have up to experience. We answer 24/7. Fast dispatch from 7am to 7pm.

If you’re starting from scratch on understanding your system, our Grafton Air Duct Cleaning approach is a good place to see how we scope a job before a wrench comes out.

Duct Repair & Sealing Cost Breakdown (2026)

Here’s how the work breaks down by line item. These are typical Manchester ranges for residential duct systems, and the written estimate sets the final number.

Line Item Typical Range What It Covers
Diagnostic inspection & leak assessment $0 (free with estimate) Visual inspection, joint check, airflow test, written report
Sealing individual leaky joints (mastic or tape) $180 – $350 Accessible joints, plenum edges, boot-to-floor connections
Full system sealing (all accessible joints) $400 – $750 Every joint we can reach, including main trunk and branch runs
Reconnecting a disconnected duct run $250 – $450 per run Reattachment, re-tape, seal, and airflow verify
Replacing crushed or collapsed flex duct $300 – $550 per run New duct section, sealed at both ends
Sealing the air handler and plenum $200 – $400 Cabinet seams, plenum flanges, return air connections
Duct cleaning before repair (recommended) $350 – $600 Rotobrush/Nikro brush and negative-air cleaning to remove debris
Full-system repair and reseal, typical home $650 – $950 Assessment, cleaning, sealing, one to two run repairs

What moves a job from the low end to the high end comes down to a few things. How hard it is to reach the ductwork matters more than anything else. A system in a basement with good clearance in a Bedford-area home comes apart fast. A duct system crammed between the floor joists of an older Manchester multi-family, where you have to pull ceiling to reach a disconnected joint, costs more because the labor costs more. Add in whether you’re repairing one run or several, whether the ducts need cleaning first, and whether the air handler cabinet is also leaking. If you’re budgeting, the biggest variable is usually how many runs need work, not how big the house is.

One more thing worth saying plainly. Duct sealing is not a hard sell once you’ve seen the test. A system leaking 20 to 30 percent of its conditioned air into a basement is a comfort problem and an energy bill problem, and we can show you where the loss is happening before we quote a fix.

Want to talk it through?Free estimate, price agreed before work starts
Call (833) 865-1627

What Affects Duct Repair & Sealing Pricing in Manchester

Pricing in Manchester isn’t random. These are the factors that actually move the number up or down when we put together an estimate for a house in this market.

  • Number of leaking or disconnected runs. One bad joint is a short visit. Six leaking runs plus a disconnected trunk is a full-day job. Each added run adds material and labor, so a 1,500-square-foot ranch can cost less to fix than a 1,200-square-foot home if the smaller one has more failed connections.
  • Access to the ductwork. Ducts in an accessible basement or crawlspace are the cheapest to repair. Ducts buried under finished drywall ceilings, or in the low attic spaces common to Manchester’s older two- and three-story homes, add time and access cost because we have to work around structure rather than through it.
  • System layout and duct type. Sheet metal trunk lines hold up well and seal cleanly. Flex duct sags, tears at the fittings, and bends too sharply, so crushed or kinked flex sections are common in homes that have had ductwork added or rerouted over the years. Replacing a crushed flex run costs more in materials than sealing a metal joint.
  • Duct condition. A system that’s collected debris, rodent damage, or moisture-related mold doesn’t just need sealing. It needs cleaning and sometimes remediation before sealing makes sense. Our equipment lineup includes Rotobrush and Nikro brush-and-negative-air systems, which handle both cleaning and the inspection that follows.
  • Whether the air handler cabinet and plenum are included. A lot of air loss happens right at the furnace or air handler, not in the duct runs at all. Sealing the cabinet and plenum is a separate line item because it takes its own set of steps to do right.
  • Seasonal timing in the Manchester climate. Winter demand for service is high because that’s when homeowners notice cold rooms and high heating bills. The coldest stretches of January and February, and the heating season that runs from October well into April, are when duct issues get caught. If your system failed in March, it probably failed in December too and nobody noticed because the attic heat loss only showed up in the deepest cold.

For a wider view of what full-system servicing costs across the three service lines we offer, our Manchester page covers the local service picture in more detail.

How Duct Repair & Sealing Works in a Manchester Home

What actually happens during a typical repair visit is worth explaining, because the process is where the cost comes from. We start with an inspection. We check the main trunk line, the branch runs, every joint we can reach, and the return side of the system. We look for gaps at the plenum, tees that never got sealed, disconnected flex sections, and boot connections that have pulled away from the floor.

If cleaning is part of the job, we bring in the Rotobrush or Nikro system, agitate the duct walls with a brush, and pull the debris out under negative air pressure. Cleaning before sealing matters because you don’t want to lock dirt and debris into a sealed system. The cleaning also makes the leaks easier to spot, since debris often collects where air is escaping.

The repair itself depends on what we found. Loose joints get sealed with duct mastic, which is the right product for the job; foil tape works on some joints but mastic outlasts it. Disconnected runs get reattached, resealed, and tested for airflow before the technician leaves. Crushed or collapsed flex sections get replaced. The air handler cabinet and plenum get sealed if they’re leaking, which they usually are.

After the work, we check the system’s airflow and confirm the repair holds. What you should expect: a clear list of what we found, what we fixed, and what we left alone because it wasn’t worth the money to address. If something in your system doesn’t need fixing, we’ll tell you that too.

Need a price for your air duct cleaning?Free estimate, price agreed before work starts
Call (833) 865-1627

A note on what not to try yourself

Duct sealing and repair isn’t a dangerous job the way electrical work is, but there are two real hazards worth flagging. First, if you’re opening up anything around a gas-fired furnace, the gas line and the combustion air setup are not a DIY zone. Second, if your ductwork is in an attic or crawlspace with limited access, the fall and access risk is real, and a trained technician knows how to work safely in those spaces. Get the scope of the job right before you decide what to handle yourself.

How to Save on Duct Repair & Sealing

There are a few practical ways to keep the cost down without skipping the work that matters. These aren’t tricks; they’re the things that actually make a difference in what we quote.

  • Get the free inspection first. The estimate is free, and the inspection is where you find out how many leaks you actually have. A lot of homeowners assume the whole system needs to be replaced when one disconnected run is the culprit. We tell you what’s actually wrong before you spend anything.
  • Fix the leaks before they spread. A disconnected run that’s been blowing into a basement for a winter is one repair. Let it go two winters and the insulation around it gets soaked, the duct sags, and the section needs replacing instead of resealing. Catching a problem early saves money every time.
  • Bundle sealing with cleaning. If the ducts need cleaning anyway, we can do the cleaning and the sealing in the same visit. That saves a return trip and usually brings the total down compared to booking them separately. Repair and cleaning are two of the three services we offer, so this is a natural fit.
  • Ask about the return side too. Many systems are sealed on the supply side and the returns are left alone. A leaky return pulls in dust and basement air, so sealing both sides gets you more of the comfort benefit for the same visit.
  • Don’t skip the small stuff. A $200 full-seal job on a system that’s just leaking joints is money well spent if it’s done before the leaks get worse. Waiting for a bigger problem doesn’t save anything in the long run.

If you’re not sure whether your system needs repair or just cleaning, call and we’ll tell you which one fits. Stop guessing. Call (833) 865-1627 for a free estimate and a straight answer on what your duct system actually needs.

Duct Repair vs. Duct Replacement: What Makes Sense for Your System

Repair almost always makes sense when the duct system itself is structurally sound and the problem is limited to joints, connections, and a few runs. Sealing and repairing existing ducts typically costs a fraction of replacement and solves the comfort and efficiency problem just as well. Replacement starts to make sense when the whole system is too small for the house, is routed through a space that’s no longer insulated, or has been damaged badly enough that repair would be a patch on a patch.

Duct replacement is a bigger project with a bigger budget, and if you’re in that territory, the cost of a full reassessment and a written plan matters more than an estimate number. The honest answer for most Manchester homes is repair and reseal, and a decent technician should be able to tell you that in a single visit.

Questions about your air duct cleaning?Free estimate, price agreed before work starts
Call (833) 865-1627

When to Call for Duct Repair & Sealing

Some signals are obvious. Some aren’t. The common ones homeowners describe to us in Manchester, especially in the older neighborhoods around the North End and the West Side:

  • Rooms at the far end of the house stay cold while the rooms near the furnace are fine.
  • Dust collects on surfaces faster than it should, even after cleaning.
  • You can see dust blowing out of a vent or feel air escaping at a joint.
  • Your heating bills have crept up over several seasons without a rate change.
  • You can hear air moving in a wall or ceiling where there’s no vent.
  • There’s a visible gap where the duct connects to the floor or the plenum.
  • You’re finishing a basement or attic and want the ducts sealed before the drywall goes up.
  • You’ve had a recent renovation and want the duct system checked before you turn the HVAC back on.

If two or more of those apply, a free inspection is worth the call. If you’re wondering whether the air you’re breathing is part of the issue, our team can include an air quality assessment in the visit. Call (833) 865-1627. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.

FAQs: Duct Repair & Sealing Cost in Manchester

How much does duct repair and sealing cost in Manchester, NH?

Most residential duct repair and sealing jobs in Manchester run $180 to $950, with the average around $420. Simple joint sealing is at the low end; reconnecting or replacing multiple runs and sealing the plenum is at the high end. Call (833) 865-1627 for an exact quote. The estimate is free and the written price sets the final cost.

Is it cheaper to repair or replace ductwork?

Repair is cheaper in almost every case. Sealing and repairing existing ducts typically costs a fraction of replacing the system, and it solves the comfort problem just as well when the ducts are structurally sound. Replacement is a bigger job for bigger problems like undersized ductwork or severe damage. Call (833) 865-1627 and we’ll tell you which one you actually need, not which one pays us more.

How much does duct sealing cost in Manchester by itself?

Duct sealing on its own costs $400 to $750 for a full system with all accessible joints sealed, or $180 to $350 for a limited set of joints. The bigger range depends on how accessible the ductwork is and how many runs are involved. Call (833) 865-1627 for a free estimate.

Can you come today if my ducts are leaking badly?

Same-day service is often possible if you call early. We answer 24/7, and fast dispatch from 7am to 7pm keeps a same-day visit in reach. A genuine emergency, like a duct that’s pulled completely loose and is venting heat into a wall cavity, is worth calling about immediately. Otherwise a scheduled visit is fine. Call (833) 865-1627.

Does duct cleaning cost extra on top of the repair?

Duct cleaning runs $350 to $600 for a typical Manchester home and is a separate line item from the repair. We recommend it before sealing when the system has collected noticeable debris, because you don’t want to seal dirt in. Booked together, the two usually cost less than booking them on separate visits. Call (833) 865-1627 to plan the work.

What Happens When You Call

You tell us what you’ve noticed. We schedule the visit, we assess the system, and we hand you a written estimate that lays out what we found, what we recommend, and what it costs, with no surprises. We don’t upsell work you don’t need, and we don’t skip work the system actually requires. The estimate is free, and the price is set per job in writing before we start.

We work with recognized air quality and HVAC brands including Honeywell, Aprilaire, Abatement Technologies, and Guardsman, which helps us identify what’s already installed in your home and how to seal around it correctly. We repair ducts, not just clean them, and one call covers the full picture of your system: cleaning, dryer vent service, and repair.

To see how we approach the Manchester market more broadly, the team behind this page, the Grafton Air Duct Cleaning team, puts the same diagnostic-first process into every visit. Call (833) 865-1627. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Free estimates, upfront pricing, and a written plan before any work starts.

Pricing reflects the Manchester market as of 2026. Grafton Air Duct Cleaning offers free estimates – call (833) 865-1627.

What Our Customers Say

★★★★★ 4.9 from 9+ reviews

"Told me straight that our ducts were in decent shape and didn't need doing every year like the mailer companies claim."

- Danielle Pruitt

"My wife's allergies had been bad in this house since we moved in. It's been two months since they did the ducts and it's noticeably better. Not a miracle, but real."

- Dale Miller

"Fair price and thorough work. They ran about an hour and a half past the estimated finish time, so don't schedule anything tight after."

- Shannon Rhodes
Need Air Duct Cleaning help in Manchester? Licensed & insured · free written estimates
Call (833) 865-1627

Request a Free Estimate

Tell us what's going on in Manchester. We'll get back to you fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Call Now - We Answer 24/7
Local Service Coverage
Call Now - We Answer 24/7